（內部）軸承座中心之間的光軸長度。　　length of shaft between the centres of the （inner） bearing blocks
V形減速凸輪　　V-shaped slowdown cam
標準光軸：　　Standard shafts：
表面粗糙度：　　Surface roughness：
表面硬度：　　Surface hardness：
不停機回轉光軸上運行的驅動器。 　　drive operating on the rotating shaft without standstill
不圓度：　　Out-of-roundness：
材料卷繞速度 　　speed of the material to be wound
材料偏移范圍 　　 area of the material deflection
側向推力　　Side thrust
程序控制　　Sequence control
齒形刻度盤　　 serrated scale
傳動力矩　　drive torque
從列線圖確定壽命（小時）　　 Determine the life from the nomogram （in hours）
粗糙度　　 roughness height rating
彈簧換向機構　　 spring-operated reversing mechanism.
電刷　　Wipers
防腐蝕　　corrosion protection
防銹防酸光軸：　　Rust- and acid-proof shafts：
防銹光軸：　　Rust-proof shafts：
分離支架　　separate carriage
改變旋轉方向　　Changing direction of rotation
感應表面淬火surface-hardened by induction
感應淬火、研磨、拋光的鋼軸。　　 induction-hardened， ground and finished steel shafts.
隔音　　Noise dampening
光軸、導軌、軸承座和換向擋塊　　shaft， guide rails， bearing blocks and end stops
光軸材質　　Shaft material
光軸速度　　shaft speed
光軸下垂　　shaft sag
光軸旋轉　　Shaft rotation
光軸直徑　　shaft diameter
滾動環動態能力　　dynamic capacity of the rolling rings
滾動環徑向載荷　　radial load on the rolling rings
滾環驅動器產生的側向推力　　side thrust produced by the rolling ring drive
滾環驅動器在光軸自由移動用釋放手柄　　Release lever for free displacement of the rolling ring drive on the shaft
換向點加速度　　acceleration at the reversal point
換向減速　　Reversal slowdown.
換向減速滾動環驅動器　　Rolling ring drives with reversal slowdown （feature V）
換向減速凸輪長度。　　length of reversal slowdown cam
換向時間　　reversal time
緊定螺釘　　set screws
減速凸輪　　slowdown cams
減速凸輪長度　　 Length of deceleration cam
節距設置　　Pitch setting
鋸齒形50級刻度盤　　Serrated 50-step scale
卷繞線材張力 　　tension in the material to be wound
卷繞應用　　Winding applications
卷筒盤接觸來觸發換向的移動鍵　　Shifting linkage that makes contact with the spool flange to activate the reversal.
空轉力矩　　idling torque
控制手柄　　 control levers
連續調整節距用蝸輪驅動器　　Worm gear drive for continuous adjustment of the pitch.
連續高速節距用堅定螺釘　　Set screws for continuous adjustment of the pitch
聯軸節連接。　　Coupling connection
臨界光軸速度　　critical shaft speed
磨擦系數。　　coefficient of friction
排線路徑traversing path，
排線器行走方向張力 　　 tension working against the direction of travel of the drive
排線速度的計算　　Calculation of the traversing speed
配有光軸和軸承的滾環驅動器（ARG）。　　Rolling ring drive （ARG）， complete with shaft and bearings
前端倒角　　Leading end chamfer
切換機構　　Switching mechanism
切換機構彈簧　　springs in the snap-action switching mechanism
驅動電動機　　Drive motor
驅動力矩　　Drive torque
驅動器排線寬度　　traversing width of the drive
全部研磨、精加工　　All ground and superfinished
確定換向時間　　To determine reversal time
繞線筒卷筒直徑 　　 barrel diameter of the bobbin
繞線筒與光軸最佳速度比　　Optimum ratio between the bobbin and the shaft speeds
市場可購買到的不含MoS2滾柱軸承油脂　　commercially available MoS2-free roller bearing greases
釋放手柄　　release lever
雙動氣缸　double-acting pneumatic cylinder
雙軸承座　　Double bearing support
瞬時換向、刻度盤、釋放手柄　　MCR　features
瞬時換向滾動環驅動器　　Rolling ring drives with instantaneous reversal
所需側向推力　　side thrust required
所需傳動功率　　drive power required
所選排線器最大節距 　　maximum pitch of the drive selected
停機旋轉光軸上運行的驅動器。　　drive operating on the rotating shaft with standstill
通過排線器箱體側壁安裝的滾輪防止扭轉應變。　　rotection against torsional strain by rollers mounted on the side wall of the housing.
同心度偏差　　Concentricity tolerance
維護保養　　Maintenance
無光軸和軸承的滾環驅動器　　Rolling ring drive without shaft and bearings
無扭短聯接適配器　　Adapter　for torque-free coupling
無需最小排線寬度　　 No minimum traversing width required.
線材最大卷繞直徑或最大節距。　　maximum diameter of the material to be wound or maximum pitch
載荷與支架總重的法向力。　　normal force of the total weight of the payload and the carriage
支撐托架　　Support bracket
直徑公差：　　Diametral tolerance：
重型導軌　　Heavy-duty guide rail
軸承座切削力分力　　 component of the cutting force of a separator）
軸驅動　　Shaft drive
專用清漆　　Special varnish
自鎖鈕　　Self-locking knob
最大節距　　maximum pitch
最低要求：　　Minimum requirements
最小換向距離：　　Minimum reversal distance